BD-2003E Pro Series Core SawOwner’s Manual & Parts List04.2013Revision 105Manual Part# 166526Caution: Read all safety and operating instructions b
10BD-2003 CORE SAW SAFETYWARNINGIn order to prevent electrical shock and injury, the following electrical safety precautions a
11To reduce the risk of electrocution, keep all connections dry and off the ground.A Ground Fault Circuit Interrupter (GFCI) should be provided on the
12BD-2003 CORE SAW SAFETYWARNINGUse only extensions cords that are intended for outdoor use. These extension cords are identied by a
13BD-2003 CORE SAW SAFETYIn order to help prevent accidental starting and to help make your work area “kidproof,” this machine is provi
14Most motor problems are caused by improper voltage and extension cords. Cord should be one-piece and short as possible. Cord selection should match
15BD-2003 CORE SAW SAFETYSAFETY DECAL LOCATIONSDecal EDecal Location DescriptionA Motor - Front Warning - SilicaB Motor - Rear
16* The BD-2003E Pro Series is also available with a 50hz motor.BD-2003 CORE SAW PRODUCT SPECIFICATIONSMotor Baldor 3HPVoltage 230VMotor RPM 3,
17 BD-2003 CORE SAW UNPACKING & TRANSPORTINGUNPACKINGCONTENTSYour BD-2003E has been shipped from the factory thoroughly inspected. Only m
18BD-2003 CORE SAW TRANSPORTTRANSPORTINGCAUTIONThe BD-2003E weighs approximately 162 lbs. Use proper lifting techniques a
191. Ensure the ON/OFF switch is in the OFF position.2. Verify the Movable Cutting Table moves freely along the Guide Rails.3. Inspect the Diamond
22BD-2003 CORE SAW INTRODUCTIONWe at Barranca Diamond want to congratulate you on selecting the BD-2003E Core Saw. We are certain th
20BD-2003 CORE SAW SETUP & ASSEMBLYMOVABLE CUTTING TABLE INSTALLATION(A)While holding the front, position movable Cutting Table r
21WARNINGNOTE: If using a dry blade for operation, DO NOT connect the water pump.NOTE: When using the re-circulation method, the water should be cha
22BD-2003 CORE SAW OPERATION & MAINTENANCE(A) If locked, loosen Cutting Head knob by turning counter-clockwise(A) Inspect belts(B)
23BD-2003 CORE SAW MAINTENANCE(A) Loosen Motor Strap(D) Install new belt(G) Check tension(B) Push Motor forward(E) Seat
24BD-2003 CORE SAW TROUBLESHOOTINGBLADE WILL NOT CUT1. Blade is too hard for material being cut. Use a softer bonded blade. Select proper
25LOSS OF TENSION1. Steel center has been overheating as a result of blade spinning on arbor. Check water ow, distribution and lines. Tighten the b
26CRACKS IN STEEL CENTER 1. Blade utters in cut as a result of blade losing tension. Tighten the blade shaft nut. Make sure blade is running at pro
27NOTES
28BD-2003 CORE SAW PARTS LISTITEM DESCRIPTION PART # QTY. Assembly, Frame, Brick Saw (Barranca)1FRAME, WE
29BD-2003 CORE SAW PARTS LISTITEM DESCRIPTION PART# QTY. Assembly, Cutting Head (elec) 1HEAD, MOTOR MOUNT (COMP) 160346-BD 12
3BD-2003 CORE SAW TABLE OF CONTENTSSAFETYSafety Message/Alert Symbols Safety WarningsHazard SymbolsRules for Safe Operation Electrical Re
30ITEM DESCRIPTION PART # QTY. Assembly, Blade Shaft1ASSY, BLADE SHAFT 154636-BD 12PULLEY, 1 GROOVE, 2-1/2 X 3/4 133140 13SCREW, 5/16-18 X 3/8 SET 157
31ITEM DESCRIPTION PART# QTY. Assembly, Table cont...4NUT, 1/4-20, KEPS 153491 45WHEEL, ROLLER 133090 46NUT, 5/16 -18 KEPS 153942 47WOOD STRIP, TABLE
32ITEM DESCRIPTIONPART# QTY. Assembly, Mtr 230v 1 Ph 60 Hz 3 Hp1ASSY, MOTOR, 230V 60 HZ 3 HP 166493 12PULLEY, 1 GROOVE, 2-1/4 X 5/8 133157 13SCREW, 5/
33NOTES
34BD-2003 CORE SAW GENERAL PRODUCT INFORMATIONTypes of Cutting
35BD-2003 CORE SAW ACCESSORIESITEM NUMBER DESCRIPTION1 132332 Adjustable Cutting Guide 2 133090 Ro
36BD-2003 CORE SAW CONTACT AND LIMITED WARRANTYBarranca Diamond warrants to the original retail purchaser for a period of 1 year excep
37BD-2003 CORE SAW CONTACT & LIMITED WARRANTYSpecics Applicable to Limited Warranty of Diamond Blades and Core Bits:Laser Welded Blad
38BD-2003 CORE SAW CONTACT & LIMITED WARRANTYREPLACEMENT PARTSReplacement parts for this tool may be ordered from your Barranca Diamon
39NOTES
4BD-2003 CORE SAW SAFETYSafety precautions should be followed at all times when operating this equipment. Failure to read
Barranca Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-5830Phone: (310) 539-5221Fax: (310) 539-5158www.barrancadiamo
5BD-2003 CORE SAW SAFETYCALIFORNIA PROPOSITION 65 MESSAGESome dust created by power sanding, sawing, grinding, dril
6BD-2003 CORE SAW SAFETYDO NOT touch hot engine components while the machine is running or immediately after operatin
7BD-2003 CORE SAW SAFETYON / OFF• ALWAYS wear proper respiratory, head, ear and eye protection equipment when operating this machi
8• ALWAYS cut in a straight line. DO NOT cut deeper than 1” per pass with a dry blade. Step cut to achieve deeper cuts. NEVER force, jam, wedge
9BD-2003 CORE SAW SAFETYMAINTENANCE SAFETY• NEVER lubricate components or attempt service on a running machine.• Keep
Kommentare zu diesen Handbüchern